Pages: [1]   Go Down
Print

Topic: No more guilt  (Read 1030 times)

0 Members and 1 Guest are viewing this topic.
HankB
President of the IBMWR
*

Reputation 10
Offline Offline

Miles Typed: 281

My Photo Gallery


I am here to serve you.




Ignore
« on: December 24, 2006, 03:09:53 PM »

I had mentioned in an earlier post that I was almost guilty abut the lack of work I'd been doing on my K1200RS. Well... I should have been. EEK! I bought it with 21K miles on it and it now has nearly 47K. The basic maintenance interval is 12K miles, so I missed the 24K and 36K and have been approaching the 48K. So it was high time I started checking into things.

I had a set of plugs on the shelf that I'd been meaning to put in, so I dusted them off and started pulling plastic. I checked the valves and found a couple intakes pretty tight. I decided to have the dealer perform the adjustment since it requires pulling the cams. They reported that they had to go three steps on the rearmost intake. After I got the bike back, I decided it was time to install the Ohlins that I'd snagged a couple weeks earlier. So, off comes all of the plastic again. And this time, I also pulled the fuel tank. And the front wheel. I've never had so much stuff off the bike before, but the front shock is really buried.

While I had the tank off, I also replaced the air filter. That was probably the part most in need of attention. Holding both up to the light, I could see light coming through the new one but no light at all through the old.  EEK! Plugs were pretty worn, but with modern ignition systems, these can go long past their normal service interval:


I took a stab at changing the fuel filter, but the fuel pump assembly really didn't want to come out. (Thinking about this later, I wonder if there isn't a hose between it and the fuel filler for the overflow.)

The only other thing I need to do to complete this is to change the brake fluid. Or did I do that recently.  Headscratch Yeah, I think I did. But I need to engage the ABS and bleed again to make sure the fluid is freshened in the ABS modulator. But brake fluid is cheap compared to brake hardware, so there's no issue with that.

I also changed engine, transmission and final drive oil, using synthetic replacements for all.

I checked front pads and they still have about half their lining left. Don't have linked brakes and hardly use the rears, so they should still be good.

So... I should be good to go for some more tens of thousands of miles.  Bigok
Logged

'98 Dakar K1200RS "BABY K" grew up Bigsmile
'93 R100R with Velorex 700 sidecar - MBD starts
Members, please login to hide this ad.

Guests, please register to hide this ad.
« on: December 24, 2006, 03:09:53 PM »

 Logged
ksann
Super Moderator
*

Reputation 18
Offline Offline

Years Contributed: '06, '07, '08, '09
GPS: 49 hours from Jacksonville
Miles Typed: 8271

My Photo Gallery




« Reply #1 on: December 24, 2006, 08:04:38 PM »

That is an incredible close-up, looks neat.


Is she smoother noticably now?

And only an Ohlins for the front?




ken
Logged

Proud, & Pretty, father of the worlds most beautiful little girl. The bestest one!
HankB
President of the IBMWR
*

Reputation 10
Offline Offline

Miles Typed: 281

My Photo Gallery


I am here to serve you.




Ignore
« Reply #2 on: December 24, 2006, 08:26:53 PM »

Ran like a champ before I did the work. If anything, maybe the fuel mileage will go up with less intake restriction. Or maybe there will be more horsepower (like there wasn't enough before!)

I put Ohlins on front and rear, but the rear was easy enough to not be particularly noteworthy.

-hank
Logged

'98 Dakar K1200RS "BABY K" grew up Bigsmile
'93 R100R with Velorex 700 sidecar - MBD starts
Pages: [1]   Go Up
Print
Jump to:  



ST.N

Copyright © 2001 - 2012 Sport-Touring.Net.
All rights reserved.

SimplePortal 2.3.1 © 2008-2009, SimplePortal